I/o shield in the old days It was basically a coke can that had been bent into little Shapes and had a hole in it you push on this thing the damn things would cut into your finger Or even twist and once I would pop out where your pop another one Yeah, so this is really nice and one thing I want to know for people who don't know how to get these things out of there easiest way to just take your screwdriver Tap the butt of it into it, it'll pop right out so or you can push it into it, but again these new kind of really nice high heels the gigabyte and Acs are using or you don't have to worry about that that I just been There we go You can also use a different one if your is a lot of safe to do just a little bit a little pressure tap it In there, okay? Somebody just mentioned hey make sure the offsets are correct know what what they're talking about damn was it keep going so on the offsets So you got holes in the mugwort right? They're gonna come through this down in the motherboard.
You want to make sure You got nine holes in the mud board typically where do we got one two three four five six? Seven HmM. This one's eight, so this is eight So you want to make sure that there are? mounts for each one of these You also don't want to have more mounts so for this They are reloading the camera. What are we doing here was? This case is that they're already in sometimes you have to put it in yourself. Yeah Okay So look so check it out So we counted look there's there's eight holes a lot of motherboards have nine Some of them now with all these big fancy heat sinks not as many So you want to make sure that there isn't one that you don't need in this case right here check this out So once we get this board in place You're gonna go. Oh just start screwing stuff in well the problem is check the side now Look dan if you get an angle on it. It's a classic classic rookie mistake This one right here is gonna. Go nowhere. It's Gonna push into the back of the motherboard and on this pay Ya you might screw something up, so I would definitely now pull that man Is it hand-tied oh nice? This is another good example. I'm actually going to Some cases actually give you a tool to mount these things this one sensor pre-mounted for you. It doesn't have coupe sorry It doesn't have it. So I'm gonna pull this one gordon always with his trusty leatherman yeah, leatherman surge so You just loosen it up backing out with your finger. This is actually a good time to do a lesson This is pre mounted for you to make your bill the light easier You know you may have to move these around so like if this doesn't fit your motherboard You have different mounting points you have a larger motherboard Another rookie mistake you make is you put this in this case again? It's already pre-built for us I already have the mounts, but if you're putting this in five people go, okay, hand-tighten. I'm good It's time to get another beer well the problem is now You have mounted this just by hand You put a screw into this you have a problem three months from now you start unscrewing the screw in this thing and instead of the screw coming out of This mount the entire mount backs out, and you're kind of screwed because then it hits the back of the motherboard And then it's just stuck you just basically you can't actually Remove the screw from the motherboard because it won't it keeps pulling on this mount the whole thing gets stuck And I haven't seen this many many times I'm not gonna say another person. I know did it as well We had to pull up three mounts cuz he didn't have seen mount them in properly you got him you put those things in there I recommend getting you know a small wrench. You don't want to scratch some other word I know drives people crazy when I use a just umpires to do this But you were you want to get that in you really want to torque that sucker in there So it doesn't back out Oops, it gets a better grip and it also helps it from marking it up. Oh yeah, okay that's a good good safety tip egon, so I'm gonna show you another cool feature this again is awesome. This is like Kids today, it was not like this ten or fifteen years ago Check this stud out. There's a little stud in the middle Basically there's you don't have to screw anything up, but what this does is it lets you line the motherboard up? So now you just drop that in there Like look all the screws are ready for you to use yeah yet. Don't the hook And then in the old days it wasn't like that Now the problem is make sure you get all the parts not mixed up. I'm gonna imagine these are the correct screws Yeah, it must be right. Oh. No here. We go right here. There we go We have fans crews course fans cruising looks like maybe the old days gordon had a lot 10 miles to get us through You know we were that what we should do is buy like an intimate case from the late 1990s on eBay And compare it to a modern case that modern in wind case or Modern case anybody makes There is just a world of difference people have no idea. How bad it used to be to building cases They just don't know so this is what I love magnetics you driver You're gonna you're gonna like people gonna so don't use a magnetic screwdriver. You're gonna race your hard drive. No, you're gonna You don't want to do that because it sucks because if it's not magnetized you were gonna drop thats true It's gonna bounce around somewhere in your case. You're not gonna find it, and then it's three months You're gonna find it when it drops into your motherboard. Well if your magnetic screwdriver touches anything, it's totally fine Yes, so yeah, I mean, I will do this look this is a four hundred dollar hard drive is it because the magnets are so weak or Magnets just what is it?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2018
Categories |